Cps sensor jeep wrangler




Cps sensor jeep wrangler

Article Navigation:
  • Photo
  • Jeep Wrangler TJ Crankshaft Position Sensor Replacement | Jeep Wrangler TJ Forum
  • Video
  • RELATED PAGES
  • There are several reason why you would need to replace your Jeep TJ Wrangler's Crankshaft Position Sensor (or CPS for short) with the most.

    FREE SHIPPING! Resolve Timing Issues. Rough idling and engine misfires are examples of engine timing issues caused by a worn or damaged camshaft.

    FREE SHIPPING! Smoothens Engine Performance. The crankshaft position sensor has the important task of monitoring the crankshaft so that the Engine Control.

    Cps sensor jeep wrangler

    Cps sensor jeep wrangler

    I think I got lucky but you never know if you don't try! In the event the sensor is internal, we recommend trusting a professional technician with the repair. Rough Road Hardware not Present P No, create an account now. And is the CPS held on by bolts, screws, how is it secured?

    Cps sensor jeep wrangler

    Cps sensor jeep wrangler

    Cps sensor jeep wrangler

    Cps sensor jeep wrangler

    Cps sensor jeep wrangler

    As the crankshaft spins, the crankshaft position sensor magnetically reads the crankshaft position from a fixed location beside the shaft. This information is always being sent to the engine computer for comparison with data from the camshaft position sensor. When the two signals reach the computer, they must match for the computer to understand there are no mechanical errors in the engine.

    If the position of the crankshaft is different than the position of the camshaft, the computer will record that an engine timing problem is occurring, and adjust settings as designed. When the computer senses the engine is out of time, the check engine light will be displayed, and the engine may start and stall, or fail to start. Some models may prevent the ignition from attempting to start the engine. If the engine runs, it will experience loss of power, poor fuel mileage, restricted performance for engine and transmission, hesitation before accelerating and intermittent stalling.

    Cps sensor jeep wrangler

    Lastly, OBD trouble codes will be stored for the crankshaft and camshaft position. Driving a vehicle with a failed camshaft or crankshaft position sensor is most often impossible.

    If driving is possible, it is not recommended. If the sensor is functioning normally, the engine may be out of time, or may have suffered mechanical failure. The crankshaft position sensor does not have a recommended replacement interval. Depending on the vehicle or driving conditions, the sensor can last the useful life of the vehicle. Failure of the crankshaft position sensor is not uncommon however, and likelihood increases as the vehicle passes , miles.

    Cps sensor jeep wrangler

    When the vehicle is connected to a professional grade scanner, the position of the crankshaft and camshaft are read, and compared to actual engine position. If the reading is inconsistent for camshaft or crankshaft sensor, the sensor will be tested, and replaced if necessary. Replacement of the crankshaft position sensor is completed by disconnecting any electrical connector, and unscrewing the sensor. If required, sealant will be applied before re-inserting the new sensor into the engine.

    Finally the electrical connector is connected, and the vehicle is tested to confirm the repair. On some vehicles the crankshaft position sensor is located inside the engine block, and significant deconstruction is required to replace the sensor.

    In the event the sensor is internal, we recommend trusting a professional technician with the repair. OEM quality sensors should be used as lesser products will likely cause a repeated repair. Also, the vehicle's timing belt should be inspected if crankshaft position or camshaft position trouble codes are stored.

    Cps sensor jeep wrangler

    If the timing belt or timing chain has failed, the engine should be immediately placed out of service. OBD trouble codes related to the crankshaft and camshaft do not imply faulty sensors, but imply a fault in the engine.

    This can be narrowed down to the sensors, but replacing the sensor without testing may lead to unnecessary costs. Replacing a sensor is only a DIY capable project if the issue can be positively diagnosed at home. If the issue cannot be diagnosed at home, a technician should be trusted with the issue before changing parts leads to excessive repair bills without a solution. Get an Estimate Find a Shop.

    How To Replace TJ Crank Shaft Position Sensor



    • Подписаться по RSSRSS
    • Поделиться VkontakteVkontakte
    • Поделиться на FacebookFacebook
    • Твитнуть!Twitter

    Leave a Reply

    Return to Top ▲TOP ▲